0
Your cart

Did you know that you can have your order delivered to the competitions we attend?

Would you like us to come to your shooting club’s competition? Contact us, and we’ll check if this is possible.

Click here for more information.

Firearm parts and accessoriesSilencers / Compensators / Muzzle brakesInfitech ITP .22 Silencer
Infitech ITP .22 Silencer
Infitech ITP .22 Silencer
Infitech ITP .22 Silencer 2
Infitech ITP .22 Silencer 3

Infitech ITP .22 Silencer

1,690 SEK
Infitech Tippmann .22/17HMR Suppressor

A slim, telescopic suppressor specially designed for .22 and 17HMR guns.

For its small size, it offers effective suppression of both sound and muzzle flash in a very compact and lightweight package.

Fits perfectly on e.g.: Tippmann Hunter cal.22 with 18" barrel, Kriss cal.22 with 18.5" barrel and on repeating rifles cal .22 and 17HMR.

Specifications:

Thread: ½-28
Caliber: .22/17HMR
Length over the barrel: 33mm
Material: 7075-T6
Surface treatment: Black anodized
Weight: 110g
Diameter: 40mm
Length: 80mm
Sound attenuation: approx. 20dBC
Max barrel diameter: 19.5mm
Read more...

In stock: 1

Description

Article no.: ITP22

Infitech Tippmann .22/17HMR Suppressor

A neat, telescopic suppressor specially designed for .22 and 17HMR guns.

For its small size, it offers effective suppression of both sound and muzzle flash in a very compact and lightweight package.

Fits perfectly on e.g.: Tippmann Hunter cal.22 with 18" barrel, Kriss cal.22 with 18.5" barrel and on repeating rifles cal .22 and 17HMR.

Specifications:

Thread: ½-28
Caliber: .22/17HMR
Length over the barrel: 33mm
Material: 7075-T6
Finish: Black anodized
Weight: 110g
Diameter: 40mm
Length: 80mm
Silencing: approx. 20dBC
Max barrel diameter: 19,5mm

CLEANING OF INFITECH ITP22 SILENCERS

 

Cleaning of ITP22 is recommended at regular intervals, depending on ammunition type after 500 - 1000 rounds.

NOTE! If Solvent is to be used, use ONLY solvent approved for aluminum. Read on the product. RISK OF DAMAGE!!!

To disassemble and assemble the ITP22, we recommend using Infitech tools that fit into the holes on the silencer. If other tools are used, damage to the finish and/or aluminum may occur. Please note that damage to the silencer threads due to improper handling is not covered by warranty. Take special care with the threads during disassembly and assembly!

Proceed as follows:

  1. Allow the silencer to cool to room temperature if it is recently used
  2. Unscrew the caps counter-clockwise using the holes provided on each side of the silencer. Infitech's special tool is recommended for this
  3. Dissolve the deposits on all parts by using a suitable solvent (kerosene, solvent, etc.). Let the solvent work for a few minutes
  4. Scrape the deposits from the parts using a plastic or wooden scraper. NOTE! Metal damages the finish and causes scratches
  5. Wipe the parts clean with a soft cloth/cloth, and then lubricate all threads with a heat-resistant grease. We recommend Loctite LB8023
  6. Assemble the parts and screw on the caps by hand at first. Be careful to make sure that the caps take the right thread. A damaged thread will cause the silencer to lose its function
  7. Tighten both caps firmly, once they bottom out in the thread, marginal additional tightening is needed. We strongly recommend using Infitech's special tools for these steps to avoid damage to threads and finish
  8. Clean the thread on the weapon.
  9. Screw the silencer back onto the gun
Back to top